5.8 KiB
Interface (NICs) Bonding in Linux using nmcli
Today, we'll learn how to perform Interface (NICs) bonding in our CentOS 7.x using nmcli (Network Manager Command Line Interface).
NICs (Interfaces) bonding is a method for linking NICs together logically to allow fail-over or higher throughput. One of the ways to increase the network availability of a server is by using multiple network interfaces. The Linux bonding driver provides a method for aggregating multiple network interfaces into a single logical bonded interface. It is a new implementation that does not affect the older bonding driver in linux kernel; it offers an alternate implementation.
NIC bonding is done to provide two main benefits for us:
- High bandwidth
- Redundancy/resilience
Now lets configure NICs bonding in CentOS 7. We'll need to decide which interfaces that we would like to configure a Team interface.
run ip link command to check the available interface in the system.
$ ip link
Here we are using eno16777736 and eno33554960 NICs to create a team interface in activebackup mode.
Use nmcli command to create a connection for the network team interface,with the following syntax.
# nmcli con add type team con-name CNAME ifname INAME [config JSON]
Where CNAME will be the name used to refer the connection ,INAME will be the interface name and JSON (JavaScript Object Notation) specifies the runner to be used.JSON has the following syntax:
'{"runner":{"name":"METHOD"}}'
where METHOD is one of the following: broadcast, activebackup, roundrobin, loadbalance or lacp.
1. Creating Team Interface
Now let us create the team interface. here is the command we used to create the team interface.
# nmcli con add type team con-name team0 ifname team0 config '{"runner":{"name":"activebackup"}}'
run # nmcli con show command to verify the team configuration.
# nmcli con show
2. Adding Slave Devices
Now lets add the slave devices to the master team0. here is the syntax for adding the slave devices.
# nmcli con add type team-slave con-name CNAME ifname INAME master TEAM
Here we are adding eno16777736 and eno33554960 as slave devices for team0 interface.
# nmcli con add type team-slave con-name team0-port1 ifname eno16777736 master team0
# nmcli con add type team-slave con-name team0-port2 ifname eno33554960 master team0
Verify the connection configuration using #nmcli con show again. now we could see the slave configuration.
#nmcli con show
3. Assigning IP Address
All the above command will create the required configuration files under /etc/sysconfig/network-scripts/.
Lets assign an IP address to this team0 interface and enable the connection now. Here is the command to perform the IP assignment.
# nmcli con mod team0 ipv4.addresses "192.168.1.24/24 192.168.1.1"
# nmcli con mod team0 ipv4.method manual
# nmcli con up team0
4. Verifying the Bonding
Verify the IP address information in #ip add show team0 command.
#ip add show team0
Now lets check the activebackup configuration functionality using the teamdctl command.
# teamdctl team0 state
Now lets disconnect the active port and check the state again. to confirm whether the active backup configuration is working as expected.
# nmcli dev dis eno33554960
disconnected the active port and now check the state again using #teamdctl team0 state.
# teamdctl team0 state
Yes its working cool !! we will connect the disconnected connection back to team0 using the following command.
#nmcli dev con eno33554960
We have one more command called teamnl let us show some options with teamnl command.
to check the ports in team0 run the following command.
# teamnl team0 ports
Display currently active port of team0.
# teamnl team0 getoption activeport
Hurray, we have successfully configured NICs bonding :-) Please share feedback if any.
via: http://linoxide.com/linux-command/interface-nics-bonding-linux/
作者：Arun Pyasi 译者：译者ID 校对：校对者ID