Linux administrator should be familiar with **CLI** environment. Since **GUI** mode in Linux servers is not a common to be installed. **SSH** may the most popular protocol to enable Linux administrator to manage the servers via remote in secure way. Built-in with **SSH** command there is **SCP** command. **SCP** is used to copy file(s) between servers in secure way.
There are much parameters in **SCP** command that you can use. Here are the parameters that may useful on daily basis usage.
### Provide the detail information of SCP process using -v parameter ###
Basic **SCP** command without parameter will copy the files in background. User will see nothing unless the process is done or some error appears. You can use “**-v**” parameter to print debug information into the screen. It can help you debugging connection, authentication and configuration problems.
### Make file transfer faster using -C parameter ###
One of parameter that can faster your file transfer is “**-C**” parameter. The “**-C**” parameter will compress your files on the go. The unique thing is the compression is only happen in the network. When the file is arrived to the destination server, it will returning into the original size as before the compression happen.
Take a look of these commands. It is using a single file of **93 Mb**.
Transferred: sent 8905840, received 15768 bytes, in 162.5 seconds
Bytes per second: sent 54813.9, received 97.0
debug1: Exit status 0
debug1: compress outgoing: raw data 97571111, compressed 8806191, factor 0.09
debug1: compress incoming: raw data 7885, compressed 3821, factor 0.48
As you can see, when you are using compression, transfer process is done in **162.5** second. It is **10** times faster than not using “**-C**” parameter. If you are copying a lot files across the network, “**-C**” parameter would help you to decrease the total time you need.
The thing that we should notice that compression method will not work on any files. When the source file is already compressed, you will not find any improvement there. Files such as **.zip**, **.rar**, **pictures**, and **.iso** files will not affected by “**-C**” parameter.
### Select another cipher to encrypt files ###
By default **SCP** using “**AES-128**” to encrypt files. If you want to change to another cipher to encrypt it, you can use “**-c**” parameter. Take a look of this command.
Above command tell **SCP** to use **3des algorithm** to encrypt file. Please be careful that this parameter using “**-c**” not “**-C**“.
### Limiting bandwidth usage ###
Another parameter that may useful is “**-l**” parameter. The “**-l**” parameter will limit the bandwidth to use. It will be useful if you do an automation script to copy a lot of file, but you don’t want the bandwidth is drained by the **SCP** process.
The **400** value behind “**-l**” parameter is mean that we limit the bandwidth for **SCP** process only **50 KB/sec**. One thing to remember that bandwidth is specified in **Kilobits/sec** (**kbps**). It is mean that **8 bits** equal with **1 byte**.
While **SCP** counts in **Kilobyte/sec** (**KB/s**). So if you want to limit your bandwidth for **SCP** maximum only **50 KB/s**, you need to set it into **50 x 8 = 400**.
### Specify specific port to use with SCP ###
Usually **SCP** is using port **22** as a default port. But for security reason, you may change the port into another port. For example, we are using port **2249**. Then the command should be like this.
Make sure that it use capital “**P**” not “**p**“, since “**p**” is already used for preserved times and modes.
### Copy files inside directory recursively ###
Sometimes we need to copy directory and all **files** / **directories** inside it. It will be better if we can do it in **1** command. **SCP** support that scenario using “**-r**” parameter.
When the copy process is done, at the destination server you will found a directory named “**documents**” with all it’s files. The folder “**documents**” is automatically created.
### Disable progress meter and warning / diagnostic message ###
If you choose not to see progress meter and warning / diagnostic messages from SCP, you may disable it using “**-q**” parameter. Here’s the example.
As you can see, after the you enter the password, there is no any information about SCP process. After the process is complete, you will be see a prompt again.
### Copy files using SCP through Proxy ###
Proxy server is usually used in office environment. Natively, SCP is not proxy configured. When your environment using proxy, you have to “tell” SCP to communicate with the proxy.
Here’s the scenario. The proxy address is **10.0.96.6** and the proxy port is **8080**. The proxy also implemented user authentication. First, you need to create “**~/.ssh/config**” file. Second you put this command inside it.
Then you need to create file “**~/.ssh/proxyauth**” which contain.
myusername:mypassword
After that you can do SCP transparently as usual.
Please notice that corkscrew is might not installed yet on your system. On my Linux Mint, I need to install it first, using standard Linux Mint installation procedure.
$ apt-get install corkscrew
For other yum based systems, users can install corkscrew using the following yum command.
# yum install corkscrew
Another thing that since “**~/.ssh/proxyauth**” file contain your “**username**” and “**password**” in clear-text format, please make sure that the file can be accessed by you only.
### Select different ssh_config file ###
For mobile user who often switch between company network and public network, it will be suffer to always change settings in SCP. It is better if we can put a different **ssh_config** file to match our needs.
#### Here’s a sample scenario ####
Proxy is used in company network but not in public network and you are regularly switch network.
By default “**ssh_config**” file per user will be placed in “**~/.ssh/config**“. Creating a specific “**ssh_config**” file with proxy compatible, will make you easier to switch between networks.
When you are on company network, you can use “**-F**” parameter. When you are on public network, you can skip “**-F**” parameter.
That’s all about **SCP**. You can see **man pages** of **SCP** for more detail. Please feel free to leave comments and suggestions.
